Breathalyzer,Portable Alcohol Tester with USB Rechargeable,Professional-Grade Ac
$ 19.54
Description
Breathalyzer,Portable Alcohol Tester with USB Rechargeable,Professional-Grade Accuracy Breathalyzer with LCD Digital Display(10 Mouthpieces) ACCURATE TESTING: This breathalyzer is composed of advanced high-precision nanotechnology sensor, which can accurately feedback your actual situation on top of the LCD display, and can be used with family, friends PORTABLE BREATHALYZER: The professional breathalyzer is only 126x51x23 mm, and weighs only 90 g, which is very convenient to carry on the go out and it can easily be put in the bag and car TIME SAVING AND CONVENIENCE: No need to replace the battery regularly,the device comes with a USB cable allows you to charge in multiple areas, and always observe the power display. Save time cost Easy to Use: Insert the mouthpiece, long press the start button, after a "beep" the screen displays "WAIT" and starts the countdown, the screen displays "START", take a deep breath and keep blowing for 5 seconds, you can see the result This high-precision semiconductor alcohol tester is very easy to use, just press a button to operate, and secondly it has a built-in rechargeable lithium battery (3.7V,1000mAh), and with a micro USB charging cable. Allows you to perform 500-800 alcohol tests. Just blow it into Mouthpieces to get an accurate BAC reading in a few seconds. You can take it anywhere. This is very suitable for weddings, parties, banquets or other social events. Product dimensions (L * W * H): about 126 x 51 x 23 mm Weight: 3.17 oz (90g) Detection range: 0.000% -0.199% BAC; 0.000-0.995mg / l Alert Level: (Optional) 0.050% BAC; 0.500 ‰ BAC; 0.250 mg / l; 50mg / 101ml Warm-up time: <15s Response time: <5s 1, Mouthpiece, Before blowing, Please check whether the mouthpiece is properly inserted (with 8 Mouthpieces). 2, The LCD Display, You need to wait 15 seconds after blowing, The test result will be displayed on the screen. 3, Power Button, You need to long press the Power Button, and wait a few seconds before the display. 4, Mode Button, This alcohol tester has six testing standards, Respectively, The United States, Russia, China, Europe, Poland, Japan. If you need to switch modes, you need to press the "Mode Button" before the countdown of 11 seconds after power on. 5+6, Buzzer&Breath Out, You blow into the gas will be dissipated from here, which means that you need to wait for the gas to dissipate before the second test. 7, Charging Port, This alcohol breathalyzer is with a USB charging cable, you can charge at any time and anywhere. 8, Charging Indicator, When the breathalyzer is not charged, this charging indicator will show red, after a full charge shows green. Step 1 Insert the mouthpiece into the slot. Step 2 Press and hold the power button for a long time. After the Beep sounds, the product is turned on, the screen displays "WAIT" and start the countdown. Step 3 When the countdown reaches zero, the screen displays "START" and blow evenly for 3-5 seconds; Step 4 Once the sensor analyzes the breath sample, the estimated BAC value will be displayed. Note: 1. In order to get more accurate results, please test 3 times every 8-10 minutes to get the average value. 2. After showing the test result for 15 seconds without operation, it will automatically turn off. 3. Don't use the results as the basis for judging whether you should operate motor vehicles or equipment or engage in any other dangerous behavior. 4. Do not drive after drinking. Look for substitute driving after drinking. 5.After powering on, if the battery level in the upper right corner of the display shows low or the display shows “Lo” and flashes, it means the battery level is low and needs to be charged. 6.The product measurement range is 0~0.199%BAC. If the alcohol content in the body reaches the maximum value of 0.199%BAC, even if you drink more, the measurement result will not increase because it has already reached the maximum value of 0.199%BAC. 7.In WAIT preheating mode, click twice in a row (M button) to enter the alarm point setting mode, press and hold for 1 second (power button) to switch between early warning point and alarm point settings, click (power button) to increase the alarm point, and click (M button) to decrease the alarm point. Result: Result A: BAC value is lower than the Warning Value, the screen shows green and the alarm sounds "Beep"; Result B: BAC value is between the Warning Value and the Danger Value, the screen shows yellow and the alarm sounds "Beep Beep, Beep Beep, Beep Beep"; Result C: BAC value is higher than the Danger Value, the screen shows red and the alarm sounds "Beep Beep Beep" for 10 seconds. Top About this item Questions Reviews NO instructions included If for any reason you are unsatisfied with your purchase, please, contact me right away to resolve immediately. Thank you for your purchase!
